How to Clean South Florida Pavers Without Losing Joint Sand

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

To clean South Florida pavers without losing joint sand, pre-treat algae on pavers, test a wide fan spray, and use the least pressure needed. Keep the spray off the joints, keep it moving, and stop if sand appears in the runoff.

Three steps:

  • Inspect first: Check for low sand, loose edges, and signs pavers need sealing or repair, such as damaged or unstable stones, before using a cleaner labeled safe for your pavers and joint sand.
  • Wash gently: Use controlled passes. A surface cleaner spreads the spray more evenly but can still wash out sand.
  • Check after drying: Refill depleted joints according to the sand product’s instructions, including any removal, watering, and curing requirements.

South Florida’s rain and damp shade make algae and repeat washout worth watching. Re-sanding and sealing won’t fix sinking pavers or poor drainage. If pavers move or sand keeps washing away, get a repair assessment before cleaning again. Once the base is stable, paver cleaning and sealing in South Florida restores the surface.

How to Clean Pavers Without Losing Joint Sand

How to Clean Pavers Without Losing Joint Sand

Step 1: Inspect Pavers and Pre-Treat Algae

Check Joint Sand and Paver Stability

Walk the entire area. Check for low or missing joint sand, loose edges, cracked or spalled pavers, rocking stones, and standing water caused by clogged drainage. Photograph any problem spots. Areas with low sand or loose joints are the first places sand can wash out during pressure washing.

Do not start washing if pavers rock, sink, have loose edges, or show cracked or spalled surfaces. Washing can make joint erosion worse.

Sweep leaves, sediment, and loose dirt from paver faces, joints, borders, and drains. If the surface is sound, pre-treat the algae before washing. First, identify your paver and joint sand types, then check the cleaner’s label to confirm it’s safe for both. Test a discreet spot for discoloration, etching, or residue before treating the full area.

Loosen Algae With a Paver-Safe Cleaner

Protect nearby plants, pool water, metal fixtures, and painted surfaces as directed on the cleaner’s label. Follow its instructions for dilution, pre-wetting plants, shielding, and rinsing. Never mix cleaners. Keep chemical runoff out of storm drains and planted beds, and keep people and pets away for the time specified on the label.

Apply the cleaner at the labeled dilution without flooding the joints. Follow the label’s dwell time and keep the treated surface wet. Lightly scrub stubborn algae near joints with a stiff brush that won’t scratch the pavers. Rinse with a broad, controlled spray, and stop if sand appears in the runoff.

Pre-treating algae reduces the pressure needed to clean the surface. If growth keeps returning in damp joints, see algae on pavers: causes and simple solutions.

Once the algae is loosened, move to controlled washing to keep the joints intact.

How To Clean and Re-Sand Pavers After Pressure Washing

Step 2: Wash Without Blasting the Joints

Once the algae is loose, rinse the surface without opening the joints. You can pressure wash pavers, but sand loss depends on the nozzle pattern, spray angle, distance, pass speed, and joint condition.

A concentrated wand jet can wash out sand if you hold it too close or aim it along the joints.

Test a Small Area and Wash in Controlled Passes

Start in a hidden spot with the gentlest setting allowed by the equipment and paver instructions. Use a wide fan spray at the recommended distance. Let the test patch dry, then check for sunken or open joints, etched paver faces, or exposed aggregate. If you see any of these, stop and switch to a gentler method.

Work in small sections with overlapping passes. Keep your distance and angle steady, and don’t aim into or follow the joints. Rinse away loosened dirt instead of turning up the pressure or lingering over a stain. Stop if sand starts washing out.

For large areas, a surface cleaner distributes the spray more evenly than a wand.

Use a Surface Cleaner at Reduced Pressure

A compatible surface cleaner limits concentrated spray exposure, but it can still remove sand - especially from weak or partly empty joints. Choose a reduced setting suited to the pavers and equipment, test it first, and keep the attachment moving.

Direct rinse water across the surface, not along the gaps. After washing, check the joints for sand loss before re-sanding.

Step 3: Check and Replace Missing Joint Sand

After washing, let the pavers dry, then check the joints for missing sand. Pay close attention to drains, downspouts, pool decks, low spots, and runoff paths. Re-sanding fills depleted joints; it won’t fix base or drainage problems.

Signs Your Joints Lost Sand

  • [ ] Joint sand sits visibly below nearby paver surfaces or beveled edges.
  • [ ] Empty gaps, grooves, or dark channels run between pavers.
  • [ ] Loose sand has collected near drains, edges, steps, or downspouts.
  • [ ] More of the paver edge or sidewall shows than before cleaning.
  • [ ] Weeds or ants return where joints are visibly low.
  • [ ] Water flows through depleted joints during rain.

Weeds and ants can point to low joints, but they don’t prove that cleaning caused the sand loss.

Rocking, shifting, or sinking points to a base or edge-restraint problem - not just missing sand. These issues, or repeated washout, call for a repair evaluation rather than another layer of sand.

If the joints are stable and only sand is missing, refill them before traffic or rain widens the gaps.

Refill Joints According to Sand Product Instructions

Choose sand that suits the paver material, joint width, and existing installation. Wait until the surface and joints are fully dry, then refill depleted joints, especially along runoff paths. Sweep diagonally across the joints to fill them to the label’s stated depth. That’s often the bottom of the beveled edges, not flush with the surface.

Check before topping up: some polymeric sands require you to remove existing material first. Clear all sand residue from paver faces before wetting so it doesn’t leave hardened deposits or haze.

Follow the label’s directions for brushing, watering, curing, and traffic restrictions. Choose a dry-weather window, keep the area dry until the sand sets, and keep traffic off until the label allows it.

After the next heavy rain, check runoff paths again. Photograph any new channels or sand deposits to track repeated washout.

Before and After: Clean Pavers and Filled Joints

Before Properly finished
Algae film and dirt hide the surface. The paver color shows clearly after buildup is removed.
Sand is uneven or missing along runoff paths. Joints are evenly filled to the label’s stated depth, with no washout channels.
Loose sand sits on paver faces and near drains. Excess sand is removed, and edges and drains are clear.

Conclusion: Use Less Pressure and Check the Joints

Use the least pressure needed to clean buildup from pavers without disturbing the joint sand. Make controlled passes, then check the joints once the surface dries.

If sand is already missing, professional help is the safer next step. An assessment makes sense when algae covers a large area, joints have lost sand, drainage is poor, or pavers are unstable. Palm Shine Pros handles paver cleaning and sealing in South Florida for jobs that reach that point.

Sealing can help protect pavers, but it won’t replace sound joints or needed repairs. Once the joints and base are stable, follow a step-by-step paver sealing guide.

FAQs

Can I clean pavers with just a hose and brush?

Yes - a hose works for light debris and routine maintenance. For organic growth, apply a cleaning solution and scrub with a stiff nylon brush. Skip wire brushes, which can scratch pavers.

In South Florida’s climate, a hose usually won’t fully remove stubborn algae, mold, or embedded grime. For heavier buildup, professional low-pressure washing is the preferred option for thorough cleaning while limiting joint sand loss.

How can I tell which joint sand I have?

Check how the sand feels and holds up in the joints. Standard sand stays loose because it has no binding properties. It often shifts or washes out in heavy rain. Piles of sand left after a storm are a clue that it’s standard sand.

Polymeric sand hardens with help from water-activated additives. If the joints feel firm and resist erosion, they likely contain polymeric sand.

How can I prevent sand washout during heavy rain?

Fill the joints with polymeric sand. Its water-activated binders harden to help keep pavers in place and resist erosion from rain and irrigation. A 1% to 2% slope directs water away, helping reduce pooling and shifting.

After filling the joints, apply a professional-grade sealer, then reapply it every 2 to 3 years. The sealer reinforces the sand, resists moisture, and helps prevent weeds, pests, and erosion of the base beneath the pavers.

Related Blog Posts

Trusted by Our Customers

What to Expect

Frequently asked Questions